Arduino Shields

!
Arduino®
1-5 Days
A000004

Arduino USB Host Shield A000004

   Module: Pre-assembled
The Arduino USB Host Shield allows you to connect an USB device to your Arduino. The Arduino USB Host Shield allows you to connect an USB device to your Arduino board. The Arduino USB Host Shield is based on the MAX3421E (datasheet), which is an USB peripheral/host controller contains the digital logic and analog circuitry necessary to implement a full-speed USB peripheral or a full-/low-speed host compliant to USB specification rev 2.0.The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board. The following device classes are supported by the shield: HID devices, such as keyboards, mice, joysticks, etc.
Arduino®
to be confirmed
A000024
Weight: kg

Arduino Ethernet Shield 2 (without PoE)

Web Offer Price
   Module: Pre-assembled
new 

 New - Awaiting due date 

The Arduino Ethernet Shield 2 connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino Board, connect it to your network with an RJ45 cable (not included) and follow a few simple steps to start controlling your world through the internet.

The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 provides a network (IP) stack capable of both TCP and UDP. It supports up to eight simultaneous socket connections. Use the Ethernet library to write sketches that connect to the Internet using the Shield. The Ethernet Shield 2 connects to an Arduino Board using long wire-wrap headers extending through the Shield. This keeps the pin layout intact and allows another Shield to be stacked on top of it.

The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO Board. This version of the shield does not come with a Power of Ethernet (PoE) module.

Note: The Ethernet Shield 2 is, at present time, not compatible with the Arduino Zero Pro Board.

Arduino®
1-5 Days
A000043

Arduino GSM Shield with Antenna A000043

Web Offer Price
   Module: Pre-assembled
The Arduino GSM Shield connects your Arduino to the internet using the GPRS wireless network. Just plug this module onto your Arduino board, plug in a SIM card from an operator offering GPRS coverage and follow a few simple instructions to start controlling your world through the internet. You can also make/receive voice calls (you will need an external speaker and microphone circuit) and send/receive SMS messages.
Arduino®
1-5 Days
A000058

Arduino WiFi Shield with Integrated Antenna A000058

Web Offer Price
   Module: Pre-assembled
The Arduino WiFi Shield connects your Arduino to the internet wirelessly. Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Check out the reference page of the WiFi library to understand how the shield can easily provide an internet connection to your Arduino board.

The WiFi Shield communicates with Arduino using the SPI bus (through the ICSP header), so is compatible with any of the boards that have this type of bus. This version of WiFi shield have an integrated antenna on the PCB, what you have to do is just connect the shield to the Arduino.

Arduino®
1-5 Days
A000064

Arduino Proto Wireless Shield A000064

Web Offer Price
   Module: Pre-assembled
The Arduino Wireless Proto Shield is a great way to prototype wireless applications thanks to its XBee(TM) compatible socket and prototyping area. You can use the wireless module from Digi to create a network of Arduino boards, solder parts to the prototyping area to create your project.
Arduino®
1-5 Days
A000065

Arduino Proto Wireless SD Shield A000065

Web Offer Price
   Module: Pre-assembled
The Arduino Wireless SD Shield is a great way to prototype wireless applications thanks to its XBee(TM) compatible socket, prototyping area and SD card connector.

You can use the wireless module from Digi to create a network of Arduino boards, solder parts to the prototyping area to create your project, and use the SD card to store data you can then easily transfer to a computer.

Arduino®
to be confirmed
A000070
Weight: kg

Arduino Axis Motor Shield A000070

Web Offer Price
   Module: Pre-assembled
new 

 New - Awaiting due date 

The Arduino 9 Axes Motion Shield is based on the BNO055 absolute orientation sensor from Bosch Sensortec GmbH. 

The BNO055 is a System in Package (SiP), integrating a triaxial 14-bit accelerometer, a triaxial 16-bit gyroscope with a range of ±2000 degrees per second, a triaxial geomagnetic sensor and a 32-bit microcontroller running the BSX3.0 FusionLib software. The sensor features three-dimensional acceleration, yaw rate and magnetic field strength data each in 3 perpendicular axes. 
Arduino®
1-5 Days
A000075

Arduino Ethernet Shield with PoE Module A0000775

Web Offer Price
   Module: Pre-assembled
The Arduino Ethernet Shield with PoE (power-over-Ethernet) Module allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip. The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

The R3 version brings to this shield the 1.0 standard pinout that consist in 4 additional pins: 2 of them placed near the AREF pin, that are used for TWI communication, and the other 2 are placed near the RESET pin. The IOREF pin is used to adapt the shield to the board on which is mounted. The last one is not connected and is reserved for future uses.

The latest revision of the shield adds a micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Duemilanove and Mega (using the Ethernet library). It also have a separate power-over-Ethernet (PoE) module that is soldered to the board to provide power from a conventional twisted pair Category 5 Ethernet cable. It is IEEE802.3af compliant, and works with all compliant PoE injectors currently available

Arduino®
1-5 Days
A000079

Arduino Motor Shield Rev 3 A000079

Web Offer Price
   Module: Pre-assembled
The Arduino Motor Shield is based on the L298, which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.

This shield have two separate channels, called A and B, that each use 4 of the Arduino pins to choose the rotation direction, vary the speed, fast brake or sense the current that is flowing through the motor. In total there are 8 pins in use on this shield. You can use each channel separately to drive two DC motors or combine them to drive one bipolar stepper motor. The shield can supply 2A per channel, for a total of 4A maximum.

This shield has the 1.0 standard pin out that consist in 4 additional pins: 2 of them placed near the AREF pin, that are used for TWI communication, and the other 2 are placed near the RESET pin. The IOREF pin is used to adapt the shield to the board on which is mounted. The last one is not connected and is reserved for future uses.

Arduino®
1-5 Days
A000080

Arduino Mega Proto Shield PCB Rev 3 A000080

Web Offer Price
The Proto Shield PCB R3 allows you to move your projects from the breadboard to on an Arduino-compatible PCB, standing on top of the board.

The Arduino MEGA Prototyping Shield PCB makes it easy for you to design custom circuits for your next Arduino MEGA project.

You can solder parts to the prototyping area to create your project, or use it with a small solderless Breadboard (not included) to quickly test circuit ideas without having to solder. It's got extra connections for all of the Arduino MEGA I/O pins, and it's got space to mount through-hole and surface mount integrated circuits if you need to as well. It's a convenient way to make your custom circuit and Arduino MEGA into a single module.